ILV Series Electric Control Valve(20/25/32/40//50/65/80/100/125/150/200N)

     Cast steel flange two-way                           Cast steel flange tee                           Brass thread 2

           (DN15-DN100)                                   Confluence(DN25-DN300)                            (DN15-DN50)

                                                           shunt(DN65-DN300) 

 Cast steel valve flange the high temperature       Cast iron is a dynamic equilibrium              Cast iron flanges two-way 

                  (DN15-DN100)                               (DN125-DN200)                                   (DN32-DN100)

      two-way high temperature         Stainless steel internal thread shunt or confluence  Stainless steel internal thread 2 

               (DN15-DN65)                                     (DN15-DN65)                                (DN15-DN65)

Summary

◆ ILV series of electric control valve is applied widely to air-condition, cooling, heating, and BAS and so on.

◆ ILV series of electric control valve control the medium flow of cooling/heating water and vapor in order to control the is also suitable for the low temperature media (ethanethiol) etc.

◆ ILV series of electric control valve adopts the standard flange connection, but its structure corresponds with IEC international standard, small volume and weight is its characters.

◆ Single seat control valve for electric direct port has one valve seat and one plunger valve, but it has good closed character and adapt to the valves with strict rate of leakage. As the unbalance force on the stem, especially the big metric diameter, the operating pressure is forbidden to too much.

As adopting the balance structure, electric balance control valve has good balance characters. So it is suitable for the status of high differential pressure. The vibration which is taken by vortex and lashing is very small, since there are lateral guide of stem sleeve. Thus it has low noise, long life etc.

◆ Electric 3-way control valve is suitable for the proportional adjustment or by way adjustment. For example adjust the fluid temperature of heat exchanger; separate the single-way inflow into two-way outflow.

Comparing with single seat valve, it saves one valve, for the same system. So it makes the system simply.

Characteristics

◆ Range from DN20 to DN25 for electric control valve, 2-way valve, 2-way balance valve, 3-way confluent valve and 3-way by-pass valve.

◆ Equal percentage, straight line etc.

◆ Electric balance control valve is mainly applied to the status with high media pressure in the pipe. If the electric 2-way control valve does not meet the demands of pressure difference, please use the electric balance

control valve.

◆ Electric control valve of radiating type applies to high-temperature media, for example, vapor, high-temperature oil. It is suitable for the heating vapor.

Parameter 1

Parameter 2

Valve Structure

Overall Size

Mounting

1. Clean the pipe before installation, install a filter & an exhaust valve at the entrance of valve to remove gravel, rust and other dirt.

2. Vertical installation of the valve is preferred.

Horizontal or inclined installations are acceptable if required, but care must be given to support the valve, particular for the larger valve size or if vibration is present.

3. Sufficient clearance must be allowed for actuator maintain or removal only.

4. The connection of flange on valve body with pipe should be on the same axial center to prevent shear stress.

5. The arrow point on the valve body should be the same as the flow direction.

6. Under certain conditions, by passing pipes are needed for switching to manual operation for maintain or fault investigating.

7. The valve body needs the heat-reserving process, or it will effect the valve operation especially when the temperature is high. But the actuator does not need.

8. Water is not permitted to infiltrate into the actuator and wiring must correspond to the spot rule.

9. Before connecting the power, check the voltage to avoid damaging the motor. The power switch should be “off “ when checking the valve.

Q:Are you trading company or manufacturer ?

A:We have our own production and design factory, and we are also a trading company.

Q:How long is the delivery time?

A:The delivery date within 5000 PCS is 7 working days.

Q:Can you provide samples for testing？

A:Yes！We can provide the samples with free of charge,but the freight should be paid by the customer.

Q:What is the brand?

A:We have our own brand and also offer the productions with requested logo and brand name.